秒速快3

Mobile:86-133-1886-9048

Glue Potting Machine

Current Location:Home > Product Center > Glue Potting Machine

What is glue potting machine ?

Glue potting machine what we call A&B glue potting machine , double liquid potting machine or two-component glue potting machine 。 It is a fully automatic liquid controlling machine which can be sealed,fixed products with waterproof by dispensing , coating ,potting glue to the surface or internal of products 。 We normally use two-component glue 。 Glue potting machine can be worked on irregular graphics including dot , line ,arc , circle and so on 。 It is mainly use for adhesive , filling, coating and sealing 。

Glue potting machine always use two-component liquid what we call AB glue 。 Glue A is main glue and glue B is curing liquid 。 Of course it is same with one-component 。 The most widely used glue in the market are epoxy, polyurethane, silicon and other glue with ratio on 1:1、2:1、5:1、4:3、10:1 。

PGB700 glue potting machine

Glue Potting machine operating principle

1.Put A&B glue into A&B tanks , Tank A and B are with the function to assure glue in good condition .

2。It is use two metering pumps to precise gluing and make sure glue A&B dispense the corresponding weight evenly 。

3. Mixing glue A&B evenly through mixed device and automatically positioning by editing the glue trajectory through corresponding mechanical hand.

4。 It is setting the corresponding quantitative glue and program to realize automatically positioning to satisfy the glue process 。

Two questions before purchase

1.What’s type of glue do you use ? What’s the base characteristic ?

A)One-component or two-component (A&B glue);

B)What is the AB ratio if two-component。

C) What’s the viscosity and density .

D)How long does it start to curing , and what is the completely curing time .

E)What’s the packing of the glue .

2.What’s the glue process technological requirement ?

秒速快3A)What is the glue accuracy with each product ?

B)What’s the purpose of gluing ? Filling , sealing ,paste,insulation, moisture proof ?

秒速快3C)How to glue the product .

How to choose the suitable glue machine equipment ?

1、Application for optional

LED piranha module LED display module LED bulb SMD module DIP module LED Street light LED flexible strip LED rigid light LED wall washer 标牌铭牌 Led floodlight LED Segment Display Ballast 汽车灯 太阳能边框 Led underground light Inductance coil 热水器控制器 布料滴胶 T-8 tube light LED guardrail tube Power Supply PCB 硅胶文胸 LED Roller screen SMD paster 汽车齿轮 皮带 挡风玻璃 Q卡 Transformer 洗衣机 秒速快3LED Advertising light 工艺品 Energy saving lamp Ignition coil 接线盒 LED Tree light 相册 High pressure pack 硅晶片 汽车后桥 鞋子 Capacitance 电磁炉 炉具控制器 冰箱 秒速快3Mutual inductor 制冷设备

2、Glue type for optional

Double Liquid glue dispenser Three-Axis Glue DispenserPolyurethane glue dispenser Transparent glue dispenser Foam adhesive glue dispenser High viscosity glue dispenser Silicon glue dispenserFully Automatic Glue Dispenser for 5M led high additive glue dispenserEpoxy glue dispenser

3. Glue process for optional

Vacuum Glue Potting Machine Gear Pump Glue Potting Machine Plunger Pump Glue Potting Manual Glue Dispenser Universal Semi-Automatic Glue Dispenser Fully Automatic Glue Potting Machine Fully Automatic Glue Dispensing Line

4.Cost-effective for optional(Cost from high to low :)

Fully Automatic Glue Dispensing Line>秒速快3Fully Automatic Glue Potting Machine>Universal Semi-Automatic Glue Dispenser>Manual Glue Dispenser

秒速快3Speed from fast to slow : multi-heads glue dispenser > two heads glue dispenser > single head glue dispenser

Live talk by clicking Service Onlineor freely call us at 86-133-1886-9048

VideoMore

  • Transformer glue video
  • Flasher glue video
  • Water Proof Power Supply glue video
  • Rectifier glue video
  • LED display and led module glue video
  • LED flexible strip glue video

Common troubles and solutionsMore

The most common trouble of glue dispenser is the valve . We list the effective solutions as follow:
  • 1.Glue dispenser always drops

    Drops always happened when valve closed . The reason may be low concentration of glue , big air-pressure or large diameter of needles.

    Narrow needles will effect the flow of the liquid and cause back pressure . It will lead to dropping when the valve closed . Too narrow needles will effect the drainage of air when valve start to work, but it can be solved if change suitable needles .

    Conical needles with less back pressure and liquid flow smoothly 。

    It is better to drainage of the air advance or use no-foam glue or deaeration to avoid the air cause dropping after valve closed .

  • 2.Glue dispensing not evenly

    The problem cause mainly because of the storage flow pressure tank or air pressure is not stable。

    Inlet pressure regulating table should be set lower 10-15psi than factory minimum pressure . The pressure in pressure tank should be set upper than the middle pressure of regulating table . It should be avoided to use the pressure lower than the middle pressure of regulating table .

    Control pressure of rubber valve at least higher than 60psi to assured glue evenly .

    We should check the glue output speed at last . The glue is uneven if the time less than 15/1000s , the output speed more longer , the glue dispensing will be more stable .

  • 3.Slow flow velocity

    秒速快3It should be changed the pipe from 1/4 to 3/8 if the flow velocity too slowly 。

    The pipe is the shorter the better if no requirement .

  • 4.Air in the fluid

    Excessive fluid pressure and short valve opening time may lead to the air infiltration liquid . We can use the conical needles and reduce fluid pressure .

  • 5. Instant glue (quick adhesive) blocking in valve connector and pipes.

    This problem is caused by heavy moisture and recycle instant glue . We should make sure to use new instant glue and wash the pipes with dry acetone . Make sure air dry and add filter between plant air pressure and valve .

  • 6.UV glue (UV curing glue )

    Make sure to use black pipeline.

    Don’t add new UV glue to old UV glue in pressure tank , we should drain off the old UV glue before pouring new UV glue into pressure tank because the UV glue will produce bubble after a period of time and lead to glue dispensing unevenly 。

  • 7.Needles

    Normally , it may cause air problem if the needle less than NO.20 . It is better to use large steel needles or conical needles to avoid to use winding needles or teflon needles

  • 8. Epoxy cleaning

    秒速快3It is better to use storage pressure cylinder of methybenzene toluene to self-cleaning one time for each shift . The more frequently cleaning the better .

Glue machine accessories

  • Dynamic mixing tubeDynamic mixing tube
  • Static mixing tubeStatic mixing tube
  • Manual pressure barrelManual pressure barrel
  • Pneumatic pressure barrelPneumatic pressure barrel
  • Cylinder plunger pumpCylinder plunger pump
  • High adhesive glue systemHigh adhesive glue system
  • Dynamic twin liquids valveDynamic twin liquids valve
  • Static twin liquids valveStatic twin liquids valve
  • NeedleNeedle
Live talk by clicking Service Onlineor freely call us at 86-133-1886-9048
Copyright @ 2008-2015 Guangzhou Daheng Automation Equipment Co.,Ltd
幸运赛车开奖直播 广西快乐十分APP下载 广西11选5官网 秒速快3 广西快乐十分软件下载 865棋牌APP 秒速快3 内蒙古快3开奖结果 865棋牌 广西快乐十分软件下载